Scrigroup - Documente si articole

Username / Parola inexistente      

Home Documente Upload Resurse Alte limbi doc  


AccessAdobe photoshopAlgoritmiAutocadBaze de dateCC sharp
CalculatoareCorel drawDot netExcelFox proFrontpageHardware
HtmlInternetJavaLinuxMatlabMs dosPascal
PhpPower pointRetele calculatoareSqlTutorialsWebdesignWindows
WordXml

AspAutocadCDot netExcelFox proHtmlJava
LinuxMathcadPhotoshopPhpSqlVisual studioWindowsXml

pppd linux command

linux

+ Font mai mare | - Font mai mic



DOCUMENTE SIMILARE

Trimite pe Messenger
ipchains linux command
bootptest linux command
tac linux command
uuencode linux command
g++ linux command
icmpinfo linux command
iptables linux command
lockfile linux command
shutdown linux command
ypserv linux command


pppd

pppd [options] [tty] [speed]




System administration command. PPP stands for the Point-to-Point Protocol; it allows datagram transmission over a serial connection. pppd attempts to configure tty for PPP (searching in /dev) or, by default, the controlling terminal. You can also specify a baud rate of speed.

Options

asyncmap map

Specify which control characters cannot pass over the line. map should be a 32-bit hex number, where each bit represents a character to escape. For example, bit 00000001 represents the character 0x00; bit 80000000 represents the character 0x1f or _. You may specify multiple characters.

auth

Require self-authentication by peers before allowing packets to move.

connect command

Connect as specified by command, which may be a binary or shell command.

debug, -d

Increment the debugging level.

defaultroute

Add a new default route in which the peer is the gateway. When the connection shuts down, remove the route.

-detach

Operate in the foreground. By default, pppd forks and operates in the background.

disconnect command

Close the connection as specified by command, which may be a binary or shell command.

domain d

Specify a domain name of d.

escape character-list

Escape all characters in character-list, which should be a comma-separated list of hex numbers. You cannot escape 0x20-0x3f or 0x5e.

file file

Consult file for options.

lock

Allow only pppd to access the device.



mru bytes

Refuse packets of more than bytes bytes.

name name

Specify a machine name for the local system.

netmask mask

Specify netmask (for example, 255.255.255.0).

passive, -p

Do not exit if peer does not respond to attempts to initiate a connection. Instead, wait for a valid packet from the peer.

silent

Send no packets until after receiving one.

[local_IP_address]:[remote_IP_address]

Specify the local and/or remote interface IP addresses, as hostnames or numeric addresses.

Files

/var/run/pppn.pid

pppd's process ID. The n in pppn.pid is the number of the PPP interface unit corresponding to this pppd process.

/etc/ppp/ip-up

Binary or script to be executed when the PPP link becomes active.

/etc/ppp/ip-down

Binary or script to be executed when the PPP link goes down.

/etc/ppp/pap-secrets

Contains usernames, passwords, and IP addresses for use in PAP authentication.

/etc/ppp/options

System defaults. Options in this file are set before the command-line options.

~/.ppprc

The user's default options. These are read before command-line options but after the system defaults.

/etc/ppp/options.ttyname

Name of the default serial port.






Politica de confidentialitate



DISTRIBUIE DOCUMENTUL

Comentarii


Vizualizari: 506
Importanta: rank

Comenteaza documentul:

Te rugam sa te autentifici sau sa iti faci cont pentru a putea comenta

Creaza cont nou

Termeni si conditii de utilizare | Contact
© SCRIGROUP 2022 . All rights reserved

Distribuie URL

Adauga cod HTML in site